Multiple Mode Inverters with Back Up ports
Energy Safe Victoria has been made aware of several occasions where Licensed Electrical Workers (LEW) and Licensed Electrical Inspectors (LEI) have left the Back Up port exposed by not fitting the supplied output connector.
A Multiple Mode Inverter (MMI) commonly contains a back up port. Some manufacturers may refer to this as an Emergency Power Supply (EPS) port. The Back Up output port commonly provides a 230 volt AC output supply when the grid supply has been lost to maintain a fridge or lighting or similar.
Some MMIs have the EPS port enabled by default, therefore the output port becomes live as soon as the MMI is energised and operational.
If the supplied output port connector is not fitted, the terminals of the back up port are left exposed.
Many of the output ports identified on MMIs pose a risk of electric shock without the supplied connector fitted allow direct contact to live parts.
The LEW and LEI must ensure that all terminals of any piece of equipment must comply with the minimum safety standards of AS/NZS 3000 to prevent access to live parts before being energised.
Refer to AS/NZS 3000:2018 Clause 4.1.2 (c)&(d).
LEWs must ensure that all parts, covers and connectors supplied with the product are fitted as per the manufacturer's instructions, and that no exposed live parts or parts that may become live under normal operation exist.
LEIs must conduct a thorough prescribed inspection of the installation, and identify any unsafe situations, such as exposed live terminals.
Electrical equipment that poses a risk of electric shock should not be installed and must not be energised.
Refer to :
- The Electricity Safety Act 1998 section 43
- The Electricity Safety (General) Regulations 2019 Regulation 253 (c)
- AS/NZS 3000:2018 The Wiring Rules, Clause 4.1.2 (c)&(d).
Description of the issue
On a number of occasions it has been found that the EPS or Back Up port connector has not been fitted to the MMI following the manufacturer's instructions. This leaves the terminals of the output port exposed, allowing potential direct contact to live parts.
In some cases the output port socket is not IP2X and is enabled by default, therefore the exposed live terminals allow a risk of electric shock, failing a standard finger test recording 242V AC to earth.
The images below should illustrate the issue.The exposed live terminals of an MMI with the EPS port connector left off by the installer A standard finger test recording a fail result with 242V AC tested at the exposed EPS pins with reference to earth The supplied EPS connector that must be fitted to prevent contact with the EPS port terminals
Note: If the connector can be removed without the use of a tool, see the additional guidance below.
Energy Safe considers the above situation as an installation issue, as the manufacturer's instructions have not been adhered to – this has created an unsafe situation.
An unsafe installation is where there is a risk of electric shock, fire or injury, caused by the installation under normal operating conditions.
Energy Safe will investigate and take enforcement action against the parties involved in any situation where an unsafe installation has been certified and energised.
Additional guidance on non-compliant MMIs
Some MMIs have been identified to be supplied with a cable connector type which can be removed without the use of a tool, then allowing access to live parts. This issue has been identified on both the Back Up port connector and the MMI AC supply connector.
This is deemed to be non-compliant to AS/NZS 4777.2 Clause 188.8.131.52
Note: This problem is deemed to be a product issue, and Energy Safe are working with manufacturers to rectify the issue and ensure product safety and compliance for the Australian market.
LEWs and LEIs should be aware of this and notify suppliers where the non-compliance is identified.
Products identified to be non-compliant should not be installed and should not be left energised. LEWs are advised to contact the product supplier or manufacturer and obtain a purpose-designed locking mechanism for the product to ensure the connector(s) cannot be removed without the use of a tool.
These images below show the manufacturers (Growatt) locking device as an example.The supplied EPS connector that can be removed without the use of a tool, to access live parts The manufacturers EPS connector with a lockable shroud to be fitted The supplied EPS connector with the lockable shroud fitted that allows the connector to only be removed with the use of a tool. Note: The shroud must be clearly labelled “WARNING Live parts do not remove!”
See information regarding the Growatt MMI recall
See information regarding the Goodwe MMI recall
Please be aware of all issues identified within this safety bulletin as there may be some MMIs available on the Australian market that do not comply and have not yet been identified.
Download this Safety Alert
Download the PDF:
Date: 05/03/2024 10:38
The currency and accuracy of this document cannot be guaranteed once printed or saved to a storage device. If in doubt, please check the ESV website for the current version.
Reviewed 04 January 2024